Anyone have one for sale or know where I might be able to find one?
Anyone have one for sale or know where I might be able to find one?
Devin
Generations Racing
ITC Civic #12
ITC Civic (Bro's ride)
ITA CRX # 41
Kart, Purple Plate # 21 (son's kart)
Does a CRX even need a 27mm rear sway bar? Good lord, I hope you're not talking about a solid 27mm bar.Anyone have one for sale or know where I might be able to find one?
[/b]
What was on the car before? Have you got the chance to drive it yet?
Kevin
2010 FP Runoffs & Super Sweep Champion
2010 ITB ARRC Champion
2008 & 2009 ITA ARRC Champion
'90 FP Acura Integra RS
'92 ITA Acura Integra RS
'92 ITB Honda Civic DX
Just an aside...why go with a 27mm? If you need something that large then you really need stiffer springs. I have a 22mm (7/8") Suspension Techniques adjustable and it's more then enough. Got it from OPM a while back. 22mm is much easier to come by.
it was passed on that that is the way to go, but it could be cheaper to run different springs. I have the stock SI bar on it right now.
Devin
Generations Racing
ITC Civic #12
ITC Civic (Bro's ride)
ITA CRX # 41
Kart, Purple Plate # 21 (son's kart)
I'll agree with Mark here. Get the 22mm Suspension Techniques bar as that should be more than enough for a CRX - plus it'll be a direct bolt in application. (I use to have one custom mounted on my Integra at one time and it worked ok on that car, and it has a much longer wheelbase. Too bad, I just sold it.) If you need more than that, than you need to be looking at springs.
Kevin
2010 FP Runoffs & Super Sweep Champion
2010 ITB ARRC Champion
2008 & 2009 ITA ARRC Champion
'90 FP Acura Integra RS
'92 ITA Acura Integra RS
'92 ITB Honda Civic DX
x2Just an aside...why go with a 27mm? If you need something that large then you really need stiffer springs. I have a 22mm (7/8") Suspension Techniques adjustable and it's more then enough. Got it from OPM a while back. 22mm is much easier to come by.
[/b]
If you need more rear roll stiffness than a 22mm bar can give you then I'd suggest going higher in rear spring rate.
Christian
Christian in FL | Something white with Honda on the valve cover...
FASTtech Limited- DL1, Schroth, & Recaro Goodness
LTB Motorsports- The Cheapest Place for Momo
TrackSpeed Motorsports- OMP, Racetech, & Driver Gear
I have both a 22mm ST bar as well as a 24mm Progress bar, both of which are no longer being used, either of which I'd be willing to sell.
PM me or shoot me an email, [email protected].
Regards,
Sam
Sam Myers
MWHC Series Director
2006 National Championship H4 1991 CRX Si - 7th Place
2006 MWHC H4 1990 Civic Si HB - RIP
2004 & 2005 MWHC H5 Champion
visit my sponsors:
http://picperformance.com/store/scripts/news.asp
http://www.setrabusa.com
http://www.tracksourcellc.com
Checking into all of this, and reserching some spring rates.
Thank you all for your time.
Devin
Generations Racing
ITC Civic #12
ITC Civic (Bro's ride)
ITA CRX # 41
Kart, Purple Plate # 21 (son's kart)
Bookmarks