Let not one person on this forum complain again that the ITAC works behind closed doors in smoke-filled rooms...
There's a reason you don't want to watch sausage being made.
Let not one person on this forum complain again that the ITAC works behind closed doors in smoke-filled rooms...
There's a reason you don't want to watch sausage being made.
I suspect the Pony car gains are speced too high.
At 30%
94/95 Mustang 3144 lbs, spec of 3195. Looks like 50 lb tq adder.
96-98 Mustang 3290 lbs, spec of 3390. Looks like 100 lb tq adder.
87-92 Camaro 3363 lbs, spec of 3465. Looks like 100 lb tq adder.
At 35%
94/95 Mustang 3265lbs, spec of 3195.
96-98 Mustang 3417lbs, spec of 3390.
87-92 Camaro 3493lbs, spec of 3465.
So, 30% seems like where they were speced and it looks like torque adders were inconsistent and axle deducts were not applied at all, neither was a strut deduct.
The first camaros, etc, (thanks for the work on those Ron and Jeff...(for those that don't know, Ron was very ehlfpul with the data and provided a proposal to get these cars into ITR)) was, as you know, hotly contested.
There were those on the committee who thought they'd make huge power. or they didn't belong because they'd be too easy to cheat up, etc. OR that they should get a 40% factor because they'd all be cheated up and impossible to police. Sheesh, it was crazy, LOL.
In the end, they got what I thought was an aggressive factor, either 30 or 35%. Andy?
Jake Gulick
CarriageHouse Motorsports
for sale: 2003 Audi A4 Quattro, clean, serviced, dark green, auto, sunroof, tan leather with 75K miles.
IT-7 #57 RX-7 race car
Porsche 1973 911E street/fun car
BMW 2003 M3 cab, sun car.
GMC Sierra Tow Vehicle
New England Region
lateapex911(at)gmail(dot)com
Now come on. I'm sure you've driven your sausage a few times.....
NC Region
1980 ITS Triumph TR8
First, we have established through the history that there is nothing wrong with the DW classifications - except the Vette. There is no DW adder in ITR.
Second, there is no strut deduction in ITR for RWD cars. Just FWD cars. Also established.
All those V8's were done at 30%. The CRB was NOT going to let them in without that number. Sucked but we said we would do it and then change it when we had numbers to back us up.
215 @ 30% with a 50lb torque adder is right on.
225 @ 30% with 100lb torque adder is right on.
230 @ 30% with 100lb torque adder is right on.
And a Vette:
205 @ 30% with 150lb torque adder, 3150 lbs, much lighter than some of the Pony cars. That doesn't pass the smell test. I seriously doubt that 350 inch motor won't see higher outputs than the 302/305 Ford/GM twins, plus it has better brakes, aero, and suspension (things we don't worry about in IT).
Vette is at 25%.
NC Region
1980 ITS Triumph TR8
Just based on cubic inches? Come on. The car was 205 stock vs. much more for those cars. The simple addition of the TPI manifold in 1985 bumped power 25hp!!! That's over 350lbs in ITR weight.
292mm brakes bro. That ain't that big. Take a stroll through the ITR ITCS...
If you were to class those Pony cars today (I would be writing my letter now), they would use 25%, COULD use a -50 for solid axle, and COULD use a deduction (or addition) for brake size.
Last edited by Andy Bettencourt; 03-01-2012 at 04:42 PM.
The cubes suggest big power.
Tell me what that intake flows and with your cam specs I can give you a pretty close estimate of theoretical max hp (need the throttle body diameter too).
Like I said in a PM, you push 417 CFM through that manifold at even 80% VE you are looking at 240 ish whp.
NC Region
1980 ITS Triumph TR8
At some point common sense has to be used.
Interestingly enough, this isn't unlike my Mustang build. 1998 Mustang, 150hp. 1999 Mustang, 190hp with the only apparent change being the intake. However, digging deep into it things are not as they seem. And I suspect the situation is the same for the 205hp C4 Vette.
Jeff, what does your magic HP book say if the manifold were to only flow between 170-190cfm?
That you are in trouble.
NC Region
1980 ITS Triumph TR8
Bookmarks