Results 1 to 8 of 8

Thread: Possible diff/tranny issues - 85 Rx-7

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Sep 2010
    Location
    Colorado
    Posts
    53

    Default Possible diff/tranny issues - 85 Rx-7

    My 1985 IT-A Rx-7 has the 4.77 Limited Slip from the front of a Kia Sportage. Ran the car this weekend and it seems to have started "howling" - sorry I don't have a better way to describe it.

    Diff had Mobil1 75-90 LS GL-5 gear oil in it with less than five hours running time. Drained the diff fluid today. It is very dark gray - like way old coffee (with cream). The magnetic drain plug had an aspirin-size amount of goo on it and there seem to be some teeny silvery pieces in suspension. I drained it into an empty clear soda bottle to see what settles out.

    Here's another video that may help with diagnosis -
    Direct link - "http://www.youtube.com/watch?v=hO2t7Ko5d_I"
    [ame]http://www.youtube.com/watch?v=hO2t7Ko5d_I[/ame]

    Attentive readers may recall my earlier post with possible rear axle issues. I'm not sure if this is related -
    https://improvedtouring.com...ad.php?t=28967

    Any ideas? Thank you for the help!
    Last edited by G-Man; 04-18-2011 at 11:40 PM.

  2. #2
    Join Date
    Jan 2001
    Location
    Buffalo, New York
    Posts
    2,942

    Default

    Need to check the bearings in the diff first.

  3. #3
    Join Date
    Oct 2004
    Location
    Asheville, NC US
    Posts
    1,626

    Default

    When you put the new gear in did you use the spacer behind the main pinion bearing from the new gear or the diff you put it in? These are factory ground to set the pinion depth in the housing and unless you have the proper factory setup tools it is most likely wrong and only contacting part of the gear face. Did you use gear paste to see the tooth pattern?
    Steve Eckerich
    ITS 18 Speedsource RX7
    ITR RX8 (under construction)

  4. #4
    Join Date
    Sep 2010
    Location
    Colorado
    Posts
    53

    Default

    Thanks for the help. I've pulled the axle: turning the input or either wheel by hand gives smooth, even motion with no jerks or rough spots (diff fluid drained).
    SEckerich - I didn't set up the rear, so no info. It was done at least two seasons ago before I bought it, so it's run for a while.
    Joeg- I'm not sure how to do this, but there doesn't seem excessive play.
    I'll take it to someone who knows these things.

  5. #5
    Join Date
    Jan 2001
    Location
    Buffalo, New York
    Posts
    2,942

    Default

    You would have to look at the bearings (and races) to see if they are burnt, galled, etc.

    It's primarly a visual inspection. You can also tell a lot by looking at the condition of the ring and pinion gears.

    Once again--visual.

  6. #6
    Join Date
    Oct 2004
    Location
    Asheville, NC US
    Posts
    1,626

    Default

    Are you feeling any vibration throught the shifter? Checked the drive shaft for play in the joints? Sure sounds like gear whine in the video. I run 75/90 Mobil 1 and change after every weekend.
    Steve Eckerich
    ITS 18 Speedsource RX7
    ITR RX8 (under construction)

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •