I'm running the GC kit for coilovers and camber plates and think they work very well, no complaints.
I'm running the GC kit for coilovers and camber plates and think they work very well, no complaints.
Last edited by Darryl Pritchett; 07-12-2009 at 11:58 AM.
Darryl Pritchett
ITA #92 Dodge Neon
2008 SE DP Champion
2010 CFL Region ITA Champion
talk to lee grimes again, you can buy the koni springperches/and clips straight from them. Price will be competitive with gc's and most people like the koni parts better. I actually have gc's but I basically got them included with my shocks, other wise i'd have koni parts. only complaint about gc's is that they have two sizes of perches and I got the larger ones that don't fit as tight to the shocks, the adapter for the circlip takes care of it (on the bottom where it mounts) but i'd rather have had the other sleeves. I'd especially like the other sleeves because i've had some very minor rubbing I could eliminate by running 2.25 inch springs
Do you have contact information for Lee? Thanks.
Bill Stevens - Mbr # 103106
BnS Racing www.bnsracing.net
92 ITA Saturn
83 ITB Shelby Dodge Charger
Sponsors - Race-Keeper Data/Video Aquisition Systems www.race-keeper.com
Simpson Performance Products - simpsonraceproducts.com
Thanks.
Bill Stevens - Mbr # 103106
BnS Racing www.bnsracing.net
92 ITA Saturn
83 ITB Shelby Dodge Charger
Sponsors - Race-Keeper Data/Video Aquisition Systems www.race-keeper.com
Simpson Performance Products - simpsonraceproducts.com
I got the ground control kit and front camber plates but I am slightly concerned about doing the install. On my other cars that I have installed them on it was pretty straight forward and very easy to do.
The neon however involves some modifications it appears from the crappy directions. On the front it looks like I would have to grind the weld down for the spring perch to get the sleeve to bottom out on the perch.
On the rear I did not get the camber plates so I am re-using the stock rubber mounts. The GC directions say to remove the old spring perch from the rubber mounts which would effictively remove about half of the sleeve bearing if I did that.
Just curious if anyone has run into similar problems when installing a ground control kit on Koni struts.
I posted three pictures. The pic of the strut shows the perch weld that sits above the perch. In order for the sleeve to slide all the way down I would have to grind the weld. Is that a possibility. The other pics show the rubber mount. Included with the GC kit is a rubber upper spring perch which its id slides on to the stock rubber mount.
If I remove the any part of the stock mount there is nothing to keep the spring centered to the mount.
Thanks for any help anyone can offer.
1987 ITS RX-7
2014 Ford Focus ST
Currently borrowing tow vehicles!!
Central Carolina Region
STEELERS SIX PACK!!
As to the fronts- I don't think the sleeve is large enough to slip over the seat, even with the weld ground smooth. Measure carefully, because I certainly could be wrong, and if so, I spent money removing the seats and having a stop welded on 1 1/2" lower for no particularly good reason. Using 6 inch springs, running on the weld on my Konis I was able to get the ride height down maybe an inch at the most. The super short struts in the front of a Neon don't lend themselves to this sort of stuff easily.
Rears are kind of the same story for ride height. I would be cautious about grinding too much on the steel sleeve in the middle of the upper mount- they tear out of stock cars with normal shocks, so any compromise of strength there is probably not good. I would probably give up and pony up the dough for the camber plates.
An ?amusing? story- When I ordered my stuff from GC, it came with exactly no comprehensible instructions. There was nothing on the website other than a pic of the front plates. The fronts were relativly straightforward, although there was more cutting and grinding involved with the top of the strut tower than I was really happy with. The rears had one hole that kind of lined up with one of the four holes in the tower, so I drilled, ground, cut and hammered until they went in. I was on the website the other day, and the new pic of the rear plates looks absolutly nothing like the ones I have. No part numbers or words etched on the plates, no installation instructions...... Good product, not so good support maybe.
Jim Barnsley, Streetwise Service
WCMA IT2 Neon Twincam
2009/2010 Regional and Alberta IT2 Champion
2009 Regional Overall Champion. Second this year, dammit.
Bookmarks