strapping the car down

[dazzlesa]

since i can not crawl under the car in front, how do i strap the front of the car down?

[Team SSR]

How confident are you in your tow hook?

[mbuskuhl]

I use an axle strap on each front wheel like this http://www.truckntow.com/pc-11613-14...s-wearpad.aspx and then my ratchet strap attached to the 2 "D" hooks.

Someone's probably going to tell me it's a bad idea but I have no issues with it and it doesn't knock the alignment out of spec either.

[raffaelli]

I use a 2” ratcheting 10000# strap (Home Depot, $15) on each of the front OE tow hooks to a D ring on the front of the trailer. On the rear, I do the same thing except around the lower arms.

My plan is to make the front straps a fixed length and only ratchet the rear (Dick, thanks for the idea). Cuts down half my work and keeps the car in the same spot every time.

[trhoppe]

My plan is to make the front straps a fixed length and only ratchet the rear (Dick, thanks for the idea). Cuts down half my work and keeps the car in the same spot every time.

Kind of makes it a pain in the butt pulling off the trailer, as you have to move the car forward before you remove the front straps.

-Tom

[ITC Racer]

I have a similar setup with two fixed length straps on the front of the car which get attached first and then I pull the car back with the ratchet straps. Works well and allows me to quickly get the car positioned properly. The drawback is that very seldom is the car in the exact center of the trailer (width) so I always have one front strap that is tight and one that is slightly loose. Never been a problem but not ideal..

[raffaelli]

Kind of makes it a pain in the butt pulling off the trailer, as you have to move the car forward before you remove the front straps.

-Tom

I find pushing the car an inch or two is alot easier than monkeying around with two more ratchets and a balance spot.

[keycom]

My plan is to make the front straps a fixed length and only ratchet the rear (Dick, thanks for the idea). Cuts down half my work and keeps the car in the same spot every time.

I use the same straps in front but the ratchet is welded to the frame. One end of the strap is fed through the front wheel (this is on both wheels) and both ends of the strap are then fed through the ratchet and tightened down.

The rear is secured with a fixed length chain (although it's adjustable if needed). On severe stops or emergencies maneuvers the chain will prevent the race car from moving forward. No possibility of straps coming undone or a broken ratchet.

(Lael, thanks for the idea and quality build.)

[x-ring]

I use a 2” ratcheting 10000# strap (Home Depot, $15) on each of the front OE tow hooks to a D ring on the front of the trailer. On the rear, I do the same thing ...

Are those the yellow nylon straps? I'd be careful with those, if they are the ones I'm thinking of, the kind truckers use to strap loads down to a flatbed.

There are two problems with that kind of strap. The hook doesn't have a safety catch, so if the strap goes slack for a moment the hook can fall off your car or out of the D-ring. Second, although the UTS of those nylon straps is plenty high, they will stretch more than real polyester car straps.

How do I know this? I used to use those (yes, from H-D) at all four corners of my car. Years ago I was towing up a rural highway near my house. A vehicle entered the highway in front of me, going realllly slow (not uncommon in a farming area), and I had to get hard into the brakes. The rear straps stretched enough to allow the front straps to unhook. When I released the brakes the car rolled backwards and the car's rear wheels fell off the trailer. Fortunately the car stopped there, instead of completely leaving me, crossing the double yellow and hitting a minivan head on (which is what went through my mind afterward).

Now I use three real car straps (like this: http://www.mrproducts.com/index.php?...tchet%20Straps ) and one 3/8" chain. The chain has a lower UTS than the straps, but it won't stretch.

FWIW

[tom_sprecher]

I use four 3500# working, 10,000 capacity rachet straps from Northern http://www.northerntool.com/webapp/w...70_21895_21895 with the hooks and clasps on four D-rings in the floor. The front ones attach to the "radius rods" in each corner and the rears to the lower shock mounts. Never had anything get loose and the car is in the perfect spot everytime no matter where it is.

[ddewhurst]

***State law (not sure about Federal DOT) here requires FOUR load securement points.***

Good point, will look at state laws. I have thought about one chain front & one chain rear many times & said to myself, hmmmm. As I'm typing I remembered the time I was towing at black night to Blackhawk Farms, stoped by a state troper because the two chains from the trailer to the truck were sparking. He looked at the car tie down & said every thing else looked ok. Hmmmm I'll add an extra locked chain just to make sure if either of the others let go the car stays on the trailer. Thanks