Well, after doing every test in the manual and passing all but one.
no Ma from the pcu I replaced the ECU and the mixture is now 12.5 @6000rpm
I have not driven the car yet.( I really don't want to...
Type: Posts; User: spike
Well, after doing every test in the manual and passing all but one.
no Ma from the pcu I replaced the ECU and the mixture is now 12.5 @6000rpm
I have not driven the car yet.( I really don't want to...
what is the ICM?
this is the setup BSI told me to run
I emailed BSI they said to check the full throttle switch and the fuel press.
Please keep your ideas coming. I will check what sever suggested.
I will be working on the car on Saturday.
Thanks...
it would rev to red line with noload
[This message has been edited by spike (edited April 12, 2005).]
24deg's total locked out
21wb was not a typo
no knock sensor
[This message has been edited by spike (edited April 12, 2005).]
[This message has been edited by spike (edited April 12, 2005).]
I had my ITB golf out this weekend for the first time ever. (Trackday with PDA @ Limerock) that car was running OK @ idle the egt read 895 & the wb 10.5 on the first lap I went easy to let everything...
What does shortening the axle do?
Great job
first class build http://Forums.ImprovedTouring.com/it/biggrin.gif
------------------
87 ITB Golf
True speed is in the turns
I am in stalling a cage in my golf is it really worth the work removing the sunroof.
IF yes any tips?
Could someone post a copy of the wiring
schematic for the distributors of a A1
rabbit and a golf.
What are your running for timing?
Is There anyone that send me a wiring chart for the distributor A1 Rabbit and A2 Golf?
Thanks again.
Is it a vacuum advance unit like BSI?
The way I have seen them used is with the
Timing fixed.(no vacuum source connected)
If so did you need to change the harness to use it?
what do you think about the distributor
BSI is selling? http://www.bsiracing.com/bsi_products.asp
[This message has been edited by spike (edited March 18, 2003).]
I was told that the vacuum advance distributor can be advanced more that the GTI unit.
But I need to change the harness,
From were to were?
The connectors are the same on the GTI unit?
I think I...
I am installing a A1 vacuum advance distributor in my A2 golf. I known I need to rerun wires to the distributor but from where and to where? What is the change between the A1 and A2 harness?
...
I was going to check toe & camber this weekend.
But when I set up the car I had 1/8 total
toe out and 2.5* camber.
I thought about that at first but after looking at the amount of wear and the...
both ways.
the wear on the driversside is 3x that on the
right,
I have had a Quaife installed and after
Two solo 1 events and two solo 2 events
I have alot of wear on the drivers side
and very little on the otherside.
Is this normal wear?...
I am going to tie down my golf to my new
trailer for the first time this weekend.
I could use some advice what would be the
best way.
I am setting up the rear of my golf
whats a good baseline setup for toe and camber
Thanks spike
what is the torque that is being used to
prevent hub/bearing failure
thanks Spike
Thanks thats what I was looking for.
Shine's web site said that the plastic can fail, but I wanted to see what you guys were
using.
What base line setup should I use.
toe out 1/6 total
camber ?
I need to do a rear wheel alignment and
have been trying to source shims.
Napa has adjustable shims @12.50 each
but are made of plastic... will they
brake?...