Search:

Type: Posts; User: Campbell

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    168,840

    Welcome Back!!! thanks

    Thanks for bringing it back.. would have been a terrible shame to lose it.
  2. Replies
    85
    Views
    56,669

    Sticky: Really nice to have this back, thanks for your...

    Really nice to have this back, thanks for your time and effort!!
  3. Replies
    0
    Views
    1,255

    Front coil over spring cap

    I need a spring cap for a front coil over set up - Tokico race shock under a welded in camber plate. For some reason the inside ring of the cap (which fits inside the coil spring) is all chipped and...
  4. Replies
    3
    Views
    2,713

    Thanks - yes I meant the valve/head assembly. I...

    Thanks - yes I meant the valve/head assembly. I assume you would see sharp angles/edges versus a rounded slope on the topside valve edge? anything else to look for? thanks
  5. Replies
    3
    Views
    2,713

    Competition Valve Jobs

    If a cylinder head had a 3 or 5 angle valve cut can you tell by looking? is it physically apparent? thanks
  6. Replies
    11
    Views
    6,189

    Mgyip - I would be interested in the Febi hubs...

    Mgyip - I would be interested in the Febi hubs and bearings, shoot me a note, thanks
  7. Replies
    11
    Views
    3,454

    Wheel bearings and Hubs

    Just curious, does anyone re-use their hubs when you change your wheel bearings? I always change mine but must admit, the ones I take off always look like new. thanks
  8. Replies
    15
    Views
    4,947

    I was able to salvage the head - a bent exhaust...

    I was able to salvage the head - a bent exhaust valve was all. The block and crank were ruined and I removed and cleaned everything else. Not sure why it happened but it was a mess in there.. thanks
  9. Replies
    8
    Views
    2,882

    Parts Cleaning

    Here it is the dead of winter and I am so bored I am going through donor parts I have as spares.. I don't have a sandblaster (although it would be so fun to have one!!) and was wondering what is a...
  10. Replies
    16
    Views
    4,882

    I received a Snap On 18v impact wrench as a gift...

    I received a Snap On 18v impact wrench as a gift and use it all the time!! it makes short work of quite a few jobs.. surprising how quick it breaks crank bolts free!!
  11. Replies
    3
    Views
    1,955

    Yes he still around, still building engines. His...

    Yes he still around, still building engines. His phone is: 847-395-4244 in Antioch, IL. My neighbor who works for Snap On talks to him often. Let me know if you need more.
  12. Replies
    1
    Views
    1,498

    Self adjusting clutch cable

    My car has a self adjusting clutch cable.. I have no idea how it works but I know it can collapse somehow and then adjust itself. How do you work those things? thanks
  13. Thread: neon acr

    by Campbell
    Replies
    10
    Views
    4,857

    What is the ACR suspension package? I see that...

    What is the ACR suspension package? I see that reference often and I am curious what the upgrade was versus the stock suspension. thanks
  14. Replies
    8
    Views
    3,100

    You are right, the last 3 turns were right hand...

    You are right, the last 3 turns were right hand turns and I stopped in the pits quickly for the temps.. he did the drivers front then the pass front.
  15. Replies
    8
    Views
    3,100

    I have used these camber settings for a couple...

    I have used these camber settings for a couple years without issue. The tires roll over on the shoulder on the drivers side but not as much on the passenger side so I think I will take some camber...
  16. Replies
    8
    Views
    3,100

    Tire Temp Question

    Last race out I finally got some tire temps - first in a while.

    Car: ITB Scirocco

    Tires: Kumho V710 - 205/55 -14

    Toe 1/8" out

    Drivers side camber: 3 1/8
    Pass side camber: 2 1/8
  17. Replies
    24
    Views
    7,649

    I was constantly running too hot, especially in...

    I was constantly running too hot, especially in 90 degree July weather!! I ended up shrouding the radiator (most important), gutted a thermostat to make a restrictor, blocked the water pump bypass...
  18. Replies
    4
    Views
    2,056

    The strut tubes aren't side specific - the front...

    The strut tubes aren't side specific - the front a-arm bolt should tighten all the way in and they should have a good size washer on them. good luck
  19. Replies
    7
    Views
    3,033

    I am towing with a Ford Sport Trac - it didn't...

    I am towing with a Ford Sport Trac - it didn't have the towing package from the factory but the previous owner installed an OE class III hitch and factory 4 plug connector. The trailer has a 4 plug...
  20. Replies
    7
    Views
    3,033

    Trailer Wiring

    Hi, I just got a new 16" trailer and am trying to sort out a couple things. They both involve wiring which is not my strong suit!!

    First, it has a flat 4 plug and only the drivers side stop...
  21. Replies
    70
    Views
    13,011

    Boy I am kind of diggin this thread.. keep in...

    Boy I am kind of diggin this thread.. keep in mind whatever goes for the MK1 GTI also goes for the MK1 Scirocco!!
  22. Replies
    7
    Views
    2,361

    I am bummed I can't make that race.. will have to...

    I am bummed I can't make that race.. will have to wait till June to get started. Have fun!!
  23. Replies
    8
    Views
    2,248

    Exhaust Gas Temps

    I just got another car that has an exhaust temp gauge in it. The thermocouple is in the #1 header tube.

    I have no idea what exhaust temps should be for a 8v, 1.8L - is there a baseline I should...
  24. Replies
    32
    Views
    8,063

    Poll: I use a Wright device (category: other) until the...

    I use a Wright device (category: other) until the dust settles on all the issues.
  25. Replies
    83
    Views
    21,719

    Greg, thanks for the insight!! what a...

    Greg, thanks for the insight!! what a progression.

    I have been towing with a dolly for 10 yrs now.. First out of necessity (all I could afford!) and recently for convenience - really don't have...
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4