Search:

Do you ship to Canada?

Next question...is it worth it after duty, brokerage and shipping? This is where the problem typically comes into play but maybe not in this case?

Hey Jim,

Yes the RA1's did last that much longer at Race City (Calgary) then the R888's. I was to say less then impressed with the R888's...and no they don't work in the swamp either...

I...

RA1's were a great tire, problem is you can't find them here anymore...rumour has it they may be available next year again but who knows.

Jim, I would think the bigger size would wear just as...

Main relay is a definite possibility as someone already said. There was also a bulletin at one point for loose connections at igniter (would explain all the codes though). The fix was to replace the...

Where can one buy these Raybestos ST pads? I have been using Hawk Blue and HT-10's. If the Raybestos are easy to find I may try them next...

Personally I would get either Koni Yellows or Billstiens. I run Koni Yellow's on my car with 400"/lb springs front and 600"/lb springs rear. I'm sure you remember seeing my car and maybe you...

If you don't have an LSD and can see the spider gear pins then you need to get a longer dental pick or make on yourself. If you need to make one get a longer section of coathanger (roughly 1')...

Sorry...I'm a little confused by your post and procedure for testing?

At any rate when the car is running, take a voltmeter and put on the battery + and -. You should have roughly 14.5V with it...

The argument of the HF CRX is kind of non relevant...how many guys running CRXsi's have removed their sunroof by cutting the roof off a DX or HF model and welding it onto their car? How is that any...

Thanks everyone! Makes my decision easier for wheels now.

I just want to make sure I interpret the rules correctly. I run an IT2 CRX in Canada (which is the same as ITA in the USA) and our wheel size rule is slightly different however I want to do some...

I normally run Hawk Blue's front and factory rear. This year I switched to Hawk HT10's in the front. They do look like they will last slightly longer however I think they are not as good as the...

Quadzilla products are hard to beat and his customer service is second to none! Check out

Quadzilla Diesel Performance

Plugs could work but I am anal...On my car I only use what is called a Plug'n'patch. Essentially it is a typical patch but from the center has a plug with a metal end. You prep the inside the same as...

In case anyone is interested this is the reply I got from Fuelsafe:


The nutring is not there to seal. Do not use any home glue to try to seal it in as you may get that glue in your fuel. Just...

I am attempting to get my fuel cell up and running again but am running into major problems left right and center. It all started with siphoning off 3yr old gas and finding the foam had rotted and...

Any concerns with exhaust fumes in the car running that setup? It would be easy to convert to that kind of set up but I'm not sure if exhaust fumes inside the car would be an issue?

Still interested in exhaust for the factory tank as well as I still think that handling wise I would be better off to put a factory tank in and get rid of the cell that is mounted higher and further...

Yeah..the BOOM factor was my main concern.

I guess I could get all the foam out I can and let it air out for a while.

Can anyone see any harm if by the first event I cannot get the foam in...

Thank you so very much guys!!! :happy204: :happy204:

The cheapest I had found foam before you posted this was $109 US. The site you posted is much cheaper.


Next question...any tips on...

Hey guys,

I just ran into a major glitch with my car re-assembly, my fuel cell foam has decided to start disintegrating into little chunks. I went to drain my tank of the fuel that has been...

Thanks for the advice Mike,

I am starting to understand this a little better now. If I am understanding this semi correctly I am running 462.xxxMHz meaning that I need a 6" antenna...now is there...

One question about the external antenna thing...what exactly is a 1/4 whip antenna. I have one that came with my setup but am having a hard time mounting where it looks good. I am considering trying...

Part numbers aren't answering whether or not I can safely run the less mass pulley safely on the motor that currently has the bigger mass pulley. Just cause they are a different part number doesn't...

Hey gang, hoping to find some gurus that have experience with different years of 88-91 D16A6 motors. I have several used engines sitting in my garage and am in the process of putting my car back...