I got one like this.
http://www.afabcorp.com/AFCO_Dynatech_USbrake/merchant.mvc?Screen=PROD&Store_Code=A&Product_Code=80127NDP&Category_Code=hp_dbl-pass-rad
Type: Posts; User: cpa7man
I got one like this.
http://www.afabcorp.com/AFCO_Dynatech_USbrake/merchant.mvc?Screen=PROD&Store_Code=A&Product_Code=80127NDP&Category_Code=hp_dbl-pass-rad
I found this, http://www.ground-control.com/gcshocks.htm
Does anyone have the rebuild or setup manuals referred to in the link above? I've got a set of these as well on a car I bought and I'm sure...
Don't forget Mazdatrix.com. Respeed is also highly recomended.
The issue is one that has been discussed before, here and in other places. Gear lube made for LSD's are
GL-5 grade lubricants. They are designed for the exceptionaly intense shear forces in the...
Dick am I missing something? I didn't see a GL-4 lubricant. For sure in the tranny you want a GL-4 lube.
I've used Amsoil for many years. They make a GL-4 for trans, several GL-5's for the rear...
Dick, I have a Dynomax that was done that way. Cut it open, get rocks, weld back up.
I understand they rely on the track having the upgraded software as well. There was a fairly negative thread on the production site (site appears to be down btw). I'm in the maket for an on board lap...
Does anyone have actual dyno results showing that the MSD's really do add power? I purchased an MSD unit but have never installed it. Some of the ep guys don't use it, as a matter of fact the fastest...
Thanks for the reply, yes car is stripped nothing left except pedals and steering wheel. Yes the car will be an EP car, my last one had a little mishap.
I'm building a car now as well, I've been looking in on this thread from time to time. Very good info, but I'm a paint moron.
I'm going to soda blast, so I'll have bare metal. That light grey or a...
This is a great old thread, thanks for resurecting it.
Does anyone know how often probes should be replaced? I've been getting inconsistent results from my EGT's vs my air fuel reading based on my...
I tend to run about 5 seconds a lap slower than the fastest CRX and about 2-3 seconds per lap slower than the fastest RX-7's. I run on 5.5" stock rims with Victoracers. I am running the fastest lap...
I'm sure most of you have seen the new FastrackNews for November. Were now free to go to 14x7 or 15X7 in our ITA first gens. I'm just curious as to what all you guys are thinking about this.
I'm...
Correct, held in place by 2 screws. I think I'm going to relocate and make almost flush. http://Forum.ImprovedTouring.com/it/smile.gif
------------------
Paul Pineider
ITA 05 (Soudiv)
WTB -...
Thanks all for the great responses.
Jake, you said it best and make a strong case. The only flaw is that when you remove the side moldings the side markers are screwed into the sheet metal. One of...
The GCR says you can remove body side moldings. It is silent on the side marker lenses. I guess this means you must leave the stock lenses. I'm repainting and thought this might be a good opportunity...
Daryl, I put the right address [email protected] or at work [email protected]
That's funny because I just sent my check off to buy an e-prod car. I may keep the ITA car and rent it out. Still...
Good job on the great weekend at TWS. I saw you unload, and spoke to you very briefly.(I have the ugly green RX-7) I have owned the MKI and MKII type Toyota's. Last summer I rebulit my sons 86.5...
Send me an email, mine is [email protected]
Thanks!
Great discussion all. This is a great little forum!
------------------
Paul Pineider
ITA 05 (Soudiv)
Mike hit it on the nose.
My water temps saw 210 4th of July weekend, oil temps 220 or so.
I run AMSOIL 2-cycle as well(premix 1oz. per galloon of fuel). This past few races I put AMSOIL 20/50...
Thanks for the input.
------------------
Paul Pineider
ITA 05 (Soudiv)
What tire inflation were you running? I run the stock wheel with Khumo Victoracers now. I'm looking at the Panasport 13x7 with Hoosier (on sale now) 225/50/13. I'm sick of being able to run as fast...
I would just get a junk yard fan off a Ford Taurus or similar, Home Depot brackets with a switch in the car to turn it on. But than if you saw my car you could tell it came from Home Depot.lol
...
What tire and wheel size combo are most of you running? Please state offset of wheel also.
It seems most are running 13x7 (4" offset)Panasport with 225/50/13 Hoosier's.
Thanks for the input.
...
From what I understand your right on Tak. If the bearing has not failed just pack with fresh grease and leave it be.