Search:

Type: Posts; User: cbstd

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,108

    I am not certain if this is IT legal, but some...

    I am not certain if this is IT legal, but some guys fill the hollow portion of the EW motor mounts with ureathane glue (the kind used in window installations that dries firm, but slightly spongey)....
  2. Replies
    1
    Views
    1,054

    On the backing plate there is a "port" for...

    On the backing plate there is a "port" for turning the adjusting wheel.

    A good quality serivce manual will have the details you need and is well worth the investment.
  3. Replies
    2
    Views
    1,247

    Side Draft Carb for 1st Gen CRX Si

    I am looking to replace my fuel injection with a set of either Mikuni or Weber side draft carbs.

    Does anyone have any experience with this set-up and any recommnedations for cam/valve combinations...
  4. Replies
    29
    Views
    7,593

    Sorry for the mis-leading advice. I did preface...

    Sorry for the mis-leading advice. I did preface my comments by saying that I race Solo2, but of course this is an IT forum.

    A thousand pardons....

    BTW, changing the front CA bushings is very...
  5. Replies
    29
    Views
    7,593

    From the look of your pictures, the wait was well...

    From the look of your pictures, the wait was well worth while for that roll cage. Very clean job.

    I run a street driven '87 CRX Si in CSP Solo2. I also use the 23mm t-bars with GC coilovers and...
  6. Replies
    1
    Views
    2,043

    I also have the OPM camber plates on my '87 Si....

    I also have the OPM camber plates on my '87 Si. The noise is coming from the plates. I put a thick rubber washer at the top of each strut (just below where it attaches to the camber plate) to absorb...
  7. Replies
    25
    Views
    7,651

    I have heard that the BMW wheels will work on a...

    I have heard that the BMW wheels will work on a Honda, but the difference in offset makes me very suspicous.

    Another alternative is to find a set of water cooled VW wheels. The bolt spacing is...
  8. Replies
    1
    Views
    1,570

    Corner weighing shops in So Cal?

    Does anyone know if there are any shops that offer corner weighing in the greater Los Angeles area. Normally I would buy the tools neccesary to do any job myself, but the cost of scales is a bit...
  9. Replies
    0
    Views
    1,308

    Corner weighing shops in So Cal?

    Does anyone know if there are any shops that offer corner weighing in the greater Los Angeles area. Normally I would buy the tools neccesary to do any job myself, but the cost of scales is a bit...
  10. Replies
    1
    Views
    1,548

    Corner weighing shops in So Cal

    Does anyone know if there are any shops that offer corner weighing in the greater Los Angeles area. Normally I would buy the tools neccesary to do any job myself, but the cost of scales is a bit...
  11. Thread: Poly Bushings

    by cbstd
    Replies
    8
    Views
    3,003

    Another OEM part that should be replaced is the...

    Another OEM part that should be replaced is the engine mounts! Fresh/new mounts make a world of difference.

    For my '87 Si, the only choice is OEM. I filled my motor mounts with a tube of...
  12. Thread: Brake duction

    by cbstd
    Replies
    3
    Views
    1,830

    The cheapest brake ducting can be sourced from...

    The cheapest brake ducting can be sourced from any Home Depot! In the shop-vac section you can buy vacumn hose in 2" and 3" sizes and nozzles to use as a duct. Tie wraps will secure all pieces.
    ...
  13. Replies
    20
    Views
    6,525

    I was lucky enough to find a Mugen LSD for my CRX...

    I was lucky enough to find a Mugen LSD for my CRX autocrosser.

    The difference is like night and day. Remember the first time you drove on race tires? Thats the kind of difference.
  14. Replies
    10
    Views
    3,179

    Porterfield makes a complete line of rear shoes...

    Porterfield makes a complete line of rear shoes for the Civic CRX. I use the 4R compound and it works great.

    Adjusting your rear drums properly is CRUCIAL for proper pedal feel.
Results 1 to 14 of 14