I wouldn't bring it to the dealer. The mechanics that are there probably weren't working there when the car was new.
Since you have fuel pressure it shouldn't be a fuel pump or relay problem. ...
Type: Posts; User: jrx13
I wouldn't bring it to the dealer. The mechanics that are there probably weren't working there when the car was new.
Since you have fuel pressure it shouldn't be a fuel pump or relay problem. ...
Just thought I'd share a link about adding a steering sensor.
http://www.rx7club.com/showthread.php?p=9062178#post9062178
-Jack
On all the rx-7's that I know of that removed the air pump, the belt only slips if your still running the fan clutch. With an electric fan, you do not need the dual alternator pulley.
I think you are mistaking the metering oil pump. The air pump is an emission device used to inject air into the exhaust. If you do remove the air pump and belt, you may have to watch for belt...
is it like the one shown on this page?
part number 7736-9010m18
http://mazdatrix.com/b6.htm
Just curious....are you still running the air pump or did you eliminate it? How about the air control valve? I have seen stuck air control valves directing all the air from the air pump into the...
I was under the impression the formula mazdas run the rx-8/renesis motor.
I don't think you can mount the front section upside down as the header flange has offset middle holes.
Now that you mentioned the header, I wonder if ISC has a different header configuration...
Ok I just installed the ITS front section and exhaust mid pipe. It seems to hang really low. I measured only 2 3/4 inch clearance from the ground at the lowest point. I measured my ride height...
actually, the ring and pinions are from the 1st generation rx-7s. Buy the gear ratio you want from mazda motorsports. Then you send ISC racing your new short pinion with your used long pinion (2nd...
Well I know first gen rx7 & 2nd gen non-turbo lsd units swap over.....and I know miata and 2nd gen rx7 swap over, so I am going to say yes they do.
Heres a link to 2nd gen info....
...
Ok, but looks like I won't be able to help. I don't ever remember that washer/spacer. BTW the pic I linked to is for a 2.25 inch setup.
Here is a supposed pic of the 2.5 inch setup (which I...
Hello. I run the same kit but installed it a couple years ago so my memory is fuzzy. Are you talking about the front or rear hardware assemblies?? The strut hardware is made by AWR if I am not...
I was going to post about the tire rack price but too, but you also answered my question. Unfortunately, I cannot buy from Mazdaspeed Motorsports because I don't race my car. I did search online...
Sorry if this is such a newbie question.
My 1987 Rx-7 has the Mazdaspeed Motorsports Stage 2 kit (I think made by AWR) and one of the front struts is blown/leaking. Anyone know where to buy one?...
Ok this is probably an illegal mod but I had heard to use a turbo transmission throwout bearing because it is supposedly stronger? Anybody know if this is true?
-Jack
Both numbers are correct. The old number has superceded to the new number. The new one in the box is a "reman" (see the r at the end of the part number). Mazda is not carrying new water pumps...
Anybody running the ISC exhaust know the approximate db level is? I was thinking about ordering the exhaust setup with the dynomax muffler.
Thanks,
Jack
Ok I am not 100% sure but I do not think the rotors are interchangeable. The Renesis/Rx-8 rotors have an extra "flank cut" on them for use with the new side exhaust ports. According to Mazda this...
I think that $700 2nd gen. tranny is with the GTUs 5th gear. Probably why the price is a little higher because you have to buy the 5th gear assembly.
Well, if you work on your race car, I think you can hook up an electric brake controller pretty easy. Its only a couple wires. One to the battery, one to ground, power and ground to the trailer...
From the 1997 catalog,
0000-01-7217 86-88 rx7
0000-01-7213 89-91 rx7
I did not enter these numbers in the website so you might have to call them to order the pulleys.
-Jack
Have you ever used the parking brake before? Just wondering. One of mine is frozen stuck, I just left it disconnected. Pretty common on 2nd gen. Rx-7. Been meaning to put another one on. It is a...
Ok I am just a newbie, but I ran redline MTL for three track events. What I noticed was that only when it was pretty warm outside, and after getting the car pretty hot (near the end of the session),...
I believe you want it exactly the same length as the original pinion you are mating it to. You are going to "graft" it correct? Meaning take the 4.88 pinion shaft from the first gen and take your...