I have a set or two of Kosei wheels that came off my RX-7, I will post some pictures and price if you are interested ?
Type: Posts; User: ITS51RX7
I have a set or two of Kosei wheels that came off my RX-7, I will post some pictures and price if you are interested ?
Chris,
The link that Marty posted has worked every time I have clicked on it, Your ISP must be blocking you from seeing the page.
I copied the ratio chart and emailed it to you.
The gear set that...
Hey Chris,
Does the chart for gear ratios that Marty posted look correct, or is that chart only for the Miata.
Thanks,
Looks as if the counter gear has 40 teeth and the 5th gear has 18 teeth which makes it a .814 miata 5th gear.
I was told that this set was the .756 Rx-7 5th, I guess I should have done my homework...
I have what I believe to be a .756 5th gear, and what to sell it but can anyone tell me the difference on the tooth count between the .756 and the standard 5th gear.
I just do not what to sell...
Hello,
I just posted a complete 2nd GEN suspension setup for sale in the Race parts section of the Classifieds section
Thanks,
SOLD
Must be a Toyota salesman
What type of car do you run and what temps are you seeing ??????????
As quoted by HOTWHEELHOLLY
My question to you is why are you asking about the advantages of a racing radiator if you already installed one <_<
You seem to be all over the board...
Doncan,
Here is the link to the 5.12 r+p
http://www.mazdatrix.com/getprice.asp?partnum=27-1100-1480
You will also need the long pinion from your 2nd gen, because the long pinion and the new 5.12 ...
The 5.12 was sold and shipped today to Tom Weaver,
Thanks to all that were interested.
Chris, I sent you an e-mail <_<
Here is some info on the diff for sale.
It is NOT a torsen unit it is the LSD clutch pack version.
It is currently installed in my old 2nd gen that I ran into the wall at IRP last year. All...
I have a 5.12 LSD complete diff that was done by ISC that I will sell if you are interested.
$ 750
Bill,
As you stated that both starters spin fine off of the car, But there is zero load on them at that time.
The only time the starter gear should come in contact with the fly-wheel is when the...
Bill,
There is not any engagement of the fly-wheel and the starter unless you apply 12 volts to the solenoid.
Do you have a lead ( 6 awg min ) from the neg side of the battery directly tied to...
Eric,
What type of gauge are you using, mech or electric sender
Looks as if this car is prepared ( HORSEPOWER WISE ) to a GT2 LEVEL . The other cars you are racing with look like ITS Porches, I think the person in the white Porches had to be getting frustrated ...
That's not a good sign for anybody that is currently using this tire :wacko:
Bill,
When is your next race, please give us an update. It sure would be nice to save almost $200 on every tire bill :D
Bill,
Are you setting the air pressure in the truck and trailer close to maxium before you start your trip ?
I always try to set the truck tires at 44 psi and the trailer at 50 psi.
The lower...
Chris, I sent you an e-mail
Thanks
Chris,
Thanks for the info and the offer :D
Was the shell that you have a manual trans, also is everything gutted or is the wire harness and dash still in tact.
Thanks again,
After I managed to push the core support about a 12 inches closer to the firewall :bash_1_: , I am now in search of a replacement 2nd Gen RX-7.
The car I have was an 1988 with an s5 motor, 5.12...
Steve,
When you get the video on your computer please send me a link , Thanks
Kevin,
I was glad one of my off season purchase's was a HAN's device, I was a little sore but nothing to complain about. I should be able to pick a tub fairly cheap, just a whole lot of labor moving...