Search:

Type: Posts; User: backformore

Page 1 of 13 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    3
    Views
    126,996

    Thanks. When I read the rules I come to the same...

    Thanks. When I read the rules I come to the same conclusion. I just seem to remember some discussion about it and couldn't find the thread.

    Thanks again. It will be going away in the near...
  2. Replies
    3
    Views
    126,996

    Evap Emission Canister Removal

    I know I've seen this discussed, but a search was unproductive so....

    2000 Civic Si, can the Evaporative Emission Purge Control Canister and associated control valves, filters, and vacuum lines be...
  3. Replies
    12
    Views
    36,157

    Tractor supply. Good idea.

    Tractor supply. Good idea.
  4. Replies
    10
    Views
    115,271

    Thanks chip. I thought it looked like it should...

    Thanks chip. I thought it looked like it should be that simple, but I appreciate the first hand info. Really wanted to avoid doing unintended damage. Just to clarify, the contacts the IG1 goes...
  5. Replies
    12
    Views
    36,157

    Any suggestion on local sources for the welding...

    Any suggestion on local sources for the welding cable? I know that a welding supply store sounds like the obvious answer, but I've checked 2 of them near me and neither had any bulk cable. I could...
  6. Replies
    23
    Views
    112,107

    This is a good discussion. It addresses several...

    This is a good discussion. It addresses several good issues. One of the small concerns I've had with the switch on the driver's side is that, on my car, the battery is on the PAX firewall. This...
  7. Replies
    10
    Views
    115,271

    Thanks Will. That is great info. The headlights...

    Thanks Will. That is great info. The headlights etc is a great idea. I'd already thought that in a real emergency I don't really care what happens to the ALT so the testing is the only time it...
  8. Replies
    12
    Views
    36,157

    Thanks for the info. Pretty much confirms my...

    Thanks for the info. Pretty much confirms my suspicions. Cheaper and Lighter is is. We don't get to say that very often :)
  9. Replies
    12
    Views
    36,157

    Master Switch Wire Guage

    While I'm asking these related questions, when wiring the Master switch, do you normally increase the wire size to account for longer runs, or just use the stock size? Stock appears to be 4 AWG. ...
  10. Replies
    23
    Views
    112,107

    Yup. There doesn't seem to be PERFECT location. ...

    Yup. There doesn't seem to be PERFECT location. The passenger side window also means you can't turn it on after you are all strapped in and realize the car won't start because it is off. The...
  11. Replies
    10
    Views
    115,271

    Great! My first thought was that you were...

    Great! My first thought was that you were referencing said shows, but I just wanted to be sure!

    As for the other, the switch I have does not have normally opened contact or included resistor. ...
  12. Replies
    23
    Views
    112,107

    Thanks again for the quick reply Greg. So, on...

    Thanks again for the quick reply Greg. So, on the bottom of the car? Just kidding. My thought is just inside the window since that makes it easily accessible, unless that is the side wedged into...
  13. Replies
    10
    Views
    115,271

    Thanks for the quick reply Greg. Since you have...

    Thanks for the quick reply Greg. Since you have lots of Honda experience, is there any method that risks damaging the ALT more than others?

    Also, do you mean The black (GRND) vs. Red(POS) on...
  14. Replies
    23
    Views
    112,107

    Master Switch Location

    I am at the point of installing the master switch in my car. I know there are a lot of posts about it on this forum, but I thought I would get folks most current views. I've read the GCR in regards...
  15. Replies
    10
    Views
    115,271

    2000 Civic Si Master Switch

    Hi all. I know there are tons of posts about master switch wiring and I've looked at most of them. I understand the general goal, but hope someone can answer a specific question.

    I have a...
  16. Replies
    85
    Views
    56,363

    Sticky: Where do we PayPal donations? I tried the button...

    Where do we PayPal donations? I tried the button on page 2 but got "smiles"? And what was the comment about emailing Greg?

    Thanks.
  17. Replies
    11
    Views
    21,772

    I've actually gotten pretty lucky Matt. The duct...

    I've actually gotten pretty lucky Matt. The duct tape I'm using seems to hold well for a day or two and then sorta loses its adhesion and falls off the glass. I have to reapply tape occasionally but...
  18. Replies
    10
    Views
    5,717

    Thanks Greg. And everyone else.

    Thanks Greg. And everyone else.
  19. Replies
    10
    Views
    5,717

    Thanks Blake. That's been my experience too. I...

    Thanks Blake. That's been my experience too. I think it might have been Tom Fowler who first suggested it to me.

    So do y'all just release the clutch or do you slip it?

    thanks again.
  20. Replies
    10
    Views
    5,717

    Question for Greg Amy

    Greg,

    I just happened to stumble upon the STL in car video from the 2013 Runoffs. It appears that you do not heel and toe or rev match on the downshifts? Is this true?

    I've heard it told...
  21. Replies
    20
    Views
    37,379

    I've had good luck with that method on the floor...

    I've had good luck with that method on the floor pans and other accessible areas too. The u!
    Ultimate challenge is the upside down seam with a little bit larger than perfect gap. Talk about ugly! ...
  22. Replies
    20
    Views
    37,379

    Thanks Mike. Once again it's good to be reassured...

    Thanks Mike. Once again it's good to be reassured it looks like poopsie. I must be doing it right:).
  23. Replies
    20
    Views
    37,379

    Unfortunately a copper backing plate is not an...

    Unfortunately a copper backing plate is not an option. Thanks for the reassurance that everyone blows holes in sheet. I think part of my problem is I am worrying too much about blowing holes instead...
  24. Replies
    20
    Views
    37,379

    Oh. Like a plug weld. Got it.

    Oh. Like a plug weld. Got it.
  25. Replies
    20
    Views
    37,379

    While we are at it, what's really kicking my ass...

    While we are at it, what's really kicking my ass is the plates for the tubes coming forward toward the firewall. Between difficult access, multiple seams on the car, weird joint orientation, and thin...
Results 1 to 25 of 301
Page 1 of 13 1 2 3 4