Search:

Sorry for the post here but I need some advice too.

I am looking for SS lines 4 line set.
What the best brand. Are they all the same?

Anyone know any for sale USed?

Also I need a rear bar....

Thats a lot of $$$ building one of those....
It would be a sweet machine except for ploughing around the track.

Maybe I should have built my VR into a track machine instead of the 2dr golf : )

I have a Digifant chip you can use to help with higher RPM. As well you can make a digifant fuel enrichment module. But I just have to read up on the fuel mapping to try and trick it. I know Ill have...

sweet, thanks

Hey Joe, Bill is right the 1.8L 16V head is different then the 2L 16V. I know thats not you rcomment, but it may help clarify things. Thats a very strange setup. A few of my friends are doing the 2L...

It has some nice IT Racing pics on the site.

Thanks in advance.


Andrew

Thanks for the help. I guess Ill lower the price. Id put them on my 8V but its alot of finikey work getting it all geared up

Thats what these ones are except there is an extra. I guess it wasnt a 510 maybe a 300 or something. Anyways the carbs are 40 DCOE.

What are they worth?

Thanks for the pic

I have a set (3 of course) weber carbs. I was wondering if they will fit on a VW 8V motor?

Thanks

I thought I would at least try : )

Ill harass you guys soon !!!!!
Thanks Dino

Andrew

I know they are out there. Derek, Ken Campbell????
I think if you simply unhook the coolant temp sensor it defaults to run rich?? well it seems to be alot snappier. Anyone have some comments on...

Just looking for the design, parts needed and how to install it on a 1.8L 8V Digifant motor.

Thanks

Andrew

I know my old Mazda had an air valve suspension that you could adjust.

Hey derek, is there a quick/easy way to tell if its the rack? A good rack is always nice : )

I have the power steering rack from my GTI would it be worth the conversion, or stick with the manual?...

I have a 1992 Golf that has some suttle steering feedback through the column and the wheel. Its only when it hits a pothole.
I replaced the ball joints, tie rods, except left one. And even springs,...

http://www.autotech.com/shocks.htm#bilstein

I just found this thanks to Derek L....

I am really gunna try to come out but the ole mighty $$$ is getting in the way. Its kinda expensive for me to do it. But maybe a few weekends.... I dont mind the parts, but the safety gear, gas and...

Steve, Thast sweet about the rotors. Barry will gear me up through Altrom. Dirt cheap like 11$ each CDN (or 84USD) for each rotor.
I might buy a few different types of pads from altrom like their...

Thanks jason. Ive been helping out Scirocco 28 and my other buddy crs240sx the last while. as well I have read the GCR a few times about the different rules.

I know for now I am building a car not...

Here is the deal.
I am building an Auto x car that I may want to IT Race too. Its a 1992 2 Dr Golf with a GTI motor, 4 pt cage (for now), and I will be putting a seat and coilovers etc.
As for...

That is some good hard specifics Bill. Thanks !!!! Can these springs be bought off the shelf? Ill have to check a few companies up here in canada.
Colin, Id like to try the Konis but Id also like...

Hey Steve, So I take it there is no shock out there OTC that would handle these rates of springs? Is there a supplier in Canada that can revalve? And in my case, what do I do if I dont have shocks...

nasa, I was just asking about the Forza in the rules and reg section, and they mentioned that the Forza is very uncomfortable...I have a line on one for 150USD + shipping. I wanted to get it but a...

THE GCR does not help explaining whether you even need a seat if you have a back brace... Anyway, I am going to get a seat. What kind should I get for my Auto x er / daily driver (and maybe a ITB...

Where do you get the CWS chip. And can it be installed in a KEN Computer, or Bosch or both....