[font=Arial Black][b]Hey Gang:
the voice of experience says that ans ITC Honda CRX hit 108db at Road Atlanta several years ago - no muffler on the car & It had a 4 into one with a 2 1/2 tailpipe...
Type: Posts; User: HONDA69
[font=Arial Black][b]Hey Gang:
the voice of experience says that ans ITC Honda CRX hit 108db at Road Atlanta several years ago - no muffler on the car & It had a 4 into one with a 2 1/2 tailpipe...
Hey Gang, Time I added my $.02 comments on the ECR SERIES. As the 2004, 2005 & 2006 ITC WINNER for the ECR Series, I agree that we have [b]BIG PROBLEMS with the ECR Series at this time. In order i...
We'll be there for the ECR!! justgotta change engine, transmission, headspace and timing on primary driver :eclipsee_steering:
Chris:
Inspect electrical wiring to & from gauge, look for chaffing, rubbing etc between sender & Gauge. W/HP1 fram, I'm assuming you are running remote Oil filter assy!! where are you reading oil...
my Fellow ECR Racers:
Carol stated what happened and Robin Langlotz states that the series is broken?? How, why? Low participation count for the whole series by SEDIV Racers, so -- It's CFR'S Race...
[b]E-Mail Robin Langlotz ([email protected]) and ask him why the change in the schedule :014:
Carol Cone, the ECR Administrator was unaware of the change in the schedule.
ITR is about 2-3 sec faster than ITS at the front of the spear, ohboy, another short time drafting partner :D then away he went - been racing against ITS cars in ECR Series for past 5 years, fun,...
BUTCH:
Can we add an ECR to Sep Race in Nashville? Over 500 mi from Sebring, I think?? Or are we just :dead_horse:
You might also contact Jack Baxter - S& J Automotive, Atlanta, GA (404) 351-7222 Owns and used to run a SAAB 99. Can provide lots of info on set-up and handling, Was last seen at a 24 hours of...
To do an honest evaluation of rental costs for an ECR Weekend, look up last year's receipts for travel to and from each Racetrack, include a reasonable fudge factor for rising fuel costs. Add the...
[b]10 legal horse power :026: cause I'm tired of being run over by Spec Miata's :birra:
Greg:
This one's from a "Normal Racer" who knows he should be wearing some sort of Head and Neck Restraint Device!! On those graphs presented with a red Line in them is the red line the probable...
Did anyone else see the Miata that was crashed into on the passenger side during the Enduro - Door bars were hanging loosely close to the shifter!! Bars were intact, as they failed at the welds, or...
[b]how about a few demo passes at the ARRC? say straighten out exiting turn 7 & light 'er off - Braking zone will probably start about turn 9 (BLACK FLAG STATION) :lol:
Go to local GMC dealer's parts department w/ VIN of vehicle & have them order brake controller harness. Part number depends on vehicle - that's why you go to dealer w/ VIN.
1. agree w/les cheney too much fuel pressure should be between 3.5 to 5.5 psi.
2. check cap, rotor & plugs replace as needed
3. check ign timing - see shop manual - new ones avail from Helms...
Mark:
Good Luck for the weekend :eclipsee_steering:
Sad to say, I'll not be there for the ECR :( spending the weekend w/engine builder and repainting house
Glad to hear trophy was appreciated.
the 2d Place Trophy is now enroute to it's rightful owner. for photo's etc, contact gprod racer :023:
egads, didn't realize I was going to cause so much gear noise (whine, whine, whine) over this one :lol:
Have you tried to contact former HP National Champion, Adam Malley? He's a good guy, own's his own shop, so daytime is limited for conversations about racing. He's in Conyers, GA
Mark:
Send Address, co-driver will send trophy! He Had it!
Mark:
Will check w/co-driver, he took car to impound, while I tore down pits. I will send if I can locate. Send me a shipping address [email protected]
If I had a second place trophy for Daytona, I'd gladly return it, but as results were not available for finishing positions at impound, I didn't get one to send to you. My congratulations on your...
Hoop:
Yeah, works best if you can find someone with a lathe. Drill out the center of the head of the bolt with a just under 1/4" drill bit & use a 1/4x24 tap to cut threads - to get correct size...
Hoop:
To really mystify you, I've been running stock Honda Civic Carburetor since I built the
Car, Only modifications have been setting it up for Holley Jettings. Biggest problem has always been...