Any news Greg?
Type: Posts; User: C. Ludwig
Any news Greg?
Blue/Blue or Blue/Black. The long pedal is a fluid problem, not a pad problem.
86-88 is clutch type. 89-91 is viscous. There were also open diffs is quite a few of them so you're no guaranteed an LSD if you buy one.
Marty,
Something else to think about in your specific example is the cross-weight versus direction you want the car to turn. T1 at M-O is the only left hand corner that matters at all, everything...
The measurements are in kgf/cm^2 which pretty roughly correlates to kpa. 1 kgf/cm^ = ~98 kpa which roughly equals 14.2 psi. Let's just call it one atmosphere at sea level or 14.7 psi @ sea level. ...
Tell him some sweet looking 6 pot Brembos and shitty pads ought to work out nicely.
The exhaust inserts are held in by roll pins. They will come loose on occasion. When it comes to removing those pins the easiest method I have used is to build up a ball of weld with the MIG gun on...
5 x 114.3 or 4.5". Ideal offset will vary but +25 or so is ideal. You'll be hard pressed to find an off the shelf wheel with that though. Most are in the +35-40 range and require spacers to work...
I agree that coolers should be allowed. It makes no sense to me at all that you are freely allowed to spend an unlimited amount on building a custom ring and pinion and differential but that couple...
The S4 (86-88) and S5 (89-92) have the spark plugs located in different places. That's not indicated in the link above. Though I've never heard a good explanation on the reason for the change or if...
Opossums are the worst!
I stored a customers car in a storage building for several weeks a few years ago while I waited for him to pick it up. When I went to retrieve the car I got in and a mouse...
You will want to plumb them in parallel if you do it. Better cooling efficiency and less pressure drop. Good Y blocks are obviously better than Ts. I may have some pics of my old car...see if I...
I've driven a car with the Type 1 and personally I much prefer a well setup and maintained clutch type diff. The big down side to the Torsen is it will go open if one wheel is lifted. Kind of...
Not sure why but I haven't received your email. I'll get something out today to the address you have listed above.
I forget what the rating is. It's actually a little hard to come by. I bought a bunch a while back from Pegasus. It's an Aeroquip hose but not sure what type other than being blue and rubber. I...
Drop me an email if you'd like some info. We have a new Haltech plug-in system for the NA and NB Miata that should retail in the $1100 range. Actually just sitting here working on the harness for...
There is hose that is meant for use as pickup hose. Most hose, high dollar braided or not, is not meant to be constantly submerged in the tank and will deteriorate over time.
Local kid has an ISC header and center section for sale. New, never installed. Asking $500 for the pair. His name is Drew. Number is 502-744-9032.
Believe the correct thread is 1/8" BSP. Pegasus has what you need.
Remove the piece from the car and go at it with a die grinder, small cutoff wheels, a torch, drill, Roto-zip, hammer and chisel or any of your favorite assortment of tools?
Street car? Full Racing Beat system. Quietest system you're going to find outside of completely stock.
It certainly shouldn't. If it does you have issues. Assuming all cylinders are running at the same AFR (they never do) you should be able to measure the same AFR at the exhaust port as you do at...
Thanks. I was thinking 8 or 9 inch. The 10 inch looked to be way long.
What length of spring do I need for Koni insert in the AWR mount for the front on a 2nd gen? Been away from this for too long. :)
After doing what you described you described in the first post without even thinking there would still be a crack running the length of the threads on the inside and having the cooler leak again we...