check out www.splparts.com they have brake ducting but of a different style and design
Type: Posts; User: invisible saddle
check out www.splparts.com they have brake ducting but of a different style and design
I have a megasquirt unit sitting in my garage. It came off a 16v that was MAP-based. However I currently have a 12v car/motor. I'm looking for a clean 16v car/chassis that I could put this on and see...
James lucky you. I sat at island outside watching them head onto the back straight. How did you get into marshalling. any openings??
the only difference is the bearing included per kit. I believe its the throwout bearing part that is the only change b/w kits. The clutch cover, disc, alignment tool and so forth remains the same.
i hope you have time to either wire up an s-afc or get some more dyno time. jwt ecu do run rich when pre-programmed. see if you can get some dyno time and trim back fuel and possibly gain a few more...
when you unplug 4th and 5th gear. the engine goes full rich WOT on the injectors. Easiest fix as listed is to use the auto ecu. i've tested it myself also using a resistor in the pulse signal so that...
if anything do some searching about robello engines. I saw online quite some time ago, and a customer had listed the bearing sizings and clearances/tolerances on the motor. considering the 8,000+ rpm...
well I hang around the 'drift scene' here in socal. and i have noticed many of the sr20det tend to burn bearings quite often (using the rwd 17mm bearings) now i noticed guys are not listening to the...
the extra fluid capacity is from the s14/s15 rear cover it has a completely different 2-bolt design from s13 4-bolt rear cover. that extra fluid capacity should not be of concern. s13 have the poppet...
My 89 sohc base model came with 5-bolt axles. I'm currently using a Nismo SSS LSD. Since you have the S15 helical goodness. They would not be able to notice from the outside its a helical unless they...
89 sohc ka 240sx hatch.
On my street car I run 12kg/10kg setup. You would think its super stiff. But its megan racing stuff. so the valving is atrocious. I have apex'i N1 type Pros on the track car rated to 10/8 and the...
are you speaking of the small rubber boot cover?? I when to superior nissan (la puente, ca) they were $3 each. I picked up 6 since i don't know when they will be discontinued. and like you said it...
http://us.st11.yimg.com/us.st.yimg.com/I/p..._1971_119686474
Assuming you shifter is this setup.
http://us.st11.yimg.com/us.st.yimg.com/I/p..._1971_119713139
remove the top 4-bolts and...
this is for running ST under NASA. If it were for IT. I have a '89 base model coupe in storage. It came from the factory w/o AC and subsequently I noticed the harness was much thinner. I figure I...
I do remember a basic upgrade was using the automatic turbo oil pump out of a 280zx or z31. that was an upgrade to a sohc motor. however i'm unsure if it cross-references to work on a dohc motor as...
hey I've been trying to clean up wiring on my project. I was wondering if anyone has the pinout diagram of the SMJ on the 240sx. I wanted to know what I can depin and remove and clear up as much as...
www.racemirrors.com
as of this present time I'm tracking it. Ryan of NASA WC said I need to do HPDEs consistently in order to recieve my comp license. So i'm just thinking as I go, beside my friends competes in ST...
This question comes up more often than the tire size question.
The axle code is located on the door jamb sticker on Nissans. If it's not there, there are visual ways of determining what you have....
Well I've been building my 89 sohc KA for awhile now. Amidst some setbacks. I got to thinking last night with it being so hot in socal (IE) and knowing the tracks are always hotter. Do you guys run...
http://www.hirevonline.com/images/gallery/2007031718_nasa_04rgb/200703nasa_02rgb_029.jpg
My friend running at cali speedway in NASA ST
http://www.sg-motorsport.com/outside04.jpg...
I forgot to include the fact I ordered a remote thermostat from jegs as well. The picture is helping me in drawing up the placement of everything. As of now I'm putting the oil filter mount where the...
okies here is the deal I have the oil relocation kit (permacool). the accusump I just ordered (2qt capacity). and my friend is dropping off a setrab oil cooler with lines this weekend. now exactly to...
yah I was curious as well as I'm building a car here in socal to compete. I have the 89-90 front bumper. look at the front fascia, the 91-93 front bumper might be easier to construct the typical...