Rob,
Would you mind doing the same for me? [email protected]
Thanks
Type: Posts; User: BrianB
Rob,
Would you mind doing the same for me? [email protected]
Thanks
Thanks Glenn for your post and the video...I was relieved to see it was my car you were referring to...:) web video and all...
Russ Jones was starting to checkout when that flat tire bite him,I...
hi,
i am pete punderson.people call me pundo.
i am an experienced spec miata driver in the northeast.i finished second in sm and ssm in naarc in 2008.i had five wins ,several seconds and thirds and...
Need some help here!
I'm running a clutch pack limited slip in my ITS car.It has the competiion clutch packing. After a couple of seasons on this setup I was wondering if I could check it's...
On the lean rotor, do the plugs show a lean condition? If you remove the header, does the exhaust port show a lean condition( a whitish residue)?
Where the primary injectors cleaned and blueprinted?...
Jamie,
If you're still having problems,give me a call during the day 413 374-1136.
Brian
#70 ITS RX-7
Does anyone run with a rear sway bar in their 2nd gen RX7? If so, is it stock or after market? what front bar and what spring rates front and back?
Thanks,
B
The picture should have a caption saying;
FOR SALE: Homemade third seat,no splinters,used once... best offer!
B
Thanks John! Email sent!
B
I believe your seeing moisture condensing at the top of the filler tube. When the engine cools down moisture in the air condenses in the engine,on the housing bottoms ,in the front cover. This...
I believe the expansion chamber is essentially a megaphone with a reducing cone at the end. it's purpose in 2 cycle engines is to create a tuned neg. wave with the expansion of the megaphone.This...
Try a new stat, larger water pump pulley,smaller e shaft pully,pulley belt tension,water wetter,sealing up the duct area in front of the radiator.small puller fan at the top of the radiator. You...
If you look into the thermostat housing,there is a bypass opening about the depth of the stock thermostat below the thermosat seat. The stock thermostat has a plate at the bottom that closes the...
Ben,
Top ISC competitor back this year?Don't kip us in suspense!
B
Ben,
Fill till it the oil level is at the bottom of the plug hole threads. Somewhere about 2 qts for the trans/ 1qt+ for the diff.
Brian
#70 ITS
NER
I am 54. I currently race an RX-7 in ITS. Started road racing in 2003 with this car which was previouly a CSP autocross/track car since 2000.
Brian Bagnall
#70 ITS RX-7 NER
I'm sure everyone mentioned is excellent! John Weisberg did my cage and did an excellent job!He's a good guy,quality work. you wont be disapointed!
B
Thanks Greg, Who did you use? Worldwide seems close enough!
B
Does anyone know of a race shop with a shock dyno service in New England? Preferably, in MA/CT area.
Thanks,
B
I'm part of Jake's consensus, I think synthetics "are awesome" in rotaries also!
B
John,
Check the trailing coils, Check the crank angle sensor, Check the wiring harness of both of the above to the ECU.
Good luck ,
Brian
#70 RX-7 ITS
Mazdatrix sells the gasket set for $111.
b
Hepolite apex seals? I've got more than a few Victoria British parts on my TR-4,prices are good especially at the jobber rate. I would never imagine that VB would sell rotary parts. I'm curious, what...
Jake,
Here's an idea. Go to a hardware store.look or an anchoring bolt that expands on one end as the nut on the other end is tightened.fit the expandable end into the bearing,Tighten the nut till...