The S5 ECU is ready!

I won't have the specifics for about a week. I just got back from Atlanta 5 minutes ago, and am headed to Chicago in the morning, then vacation starting Sunday. So when I get back I'll post some dyno results and what not. But the short story is we did a final test today and everything checked out and we're ready to start exchanging ECUs. I have seven on hand for immediate exchange.

-Pricing is $450 + shipping + $50 core.
-I have the manual on PDF as well as a Word doc of compatible PDAs. Email me for info.

[email protected]

:D

Great, I'm excited. All I have to do now is find the $$$. Seriously, I will get with you when you're back.

Travers
ITS 19

I'll pre-order for an S4 ECU at that price.

My job in Chicago went a lot more smoothly than planned so I had time to come home and put some stuff together....

Here is what I have for documentation so far. We never have looked for ultimate numbers in any of the three days we've worked on the dynos. Only confirming that we can do what we want with the fuel and ignition and that we were making the gains we thought we should with each change.

I've worked with two cars. First was an ITS prepped car that we spent some time with before swapping ECUs trying to optimize the stock setup as best we could. The numbers were not stellar but it's all it had. Playing with fuel pressure to lean out the top end we ran into a familiar situation. When trying to pull enough fuel you end up running very low pressure (~25 psi). This hurts atomization and overall performance.

After swapping ECUs the gains were best below and above peak power. This makes sense since when running the stock ECU we were tweaking the fuel pressure to optimize the peak number and thus compromising the rest of the rev range.

This particular session was our first day experimenting with the ECU. We found that the +/-25% fuel adjustment that we had built into the ECU was not enough to provide the desired a/f ratios above about 7000 rpm. The gains that were made there were done in the 12.8 - 13.0 range. We shot for 13.5 - 13.7 everywhere else. There was slightly more to be had at peak and beyond but the range of adjustment wouldn't allow it. After this day on the dyno we re-worked the ECU to allow +25/-30% adjustment to cover this area of the curve. Seems around -27% is a good jumping off area in this rev range.

All mod ECU runs were made with stock timing.

Stock ECU v. Mod ECU
Yes I resized this one chart and skewed it a bit. Not trying to bulge any curves. Just trying to get it sized decently and fairly sqaure.
http://www.ludwigmotorsports.com/rx7...u/its_dyno.jpg

Stock ECU v. Mod ECU
http://www.ludwigmotorsports.com/rx7/itsecu/its_net.jpg

This past weekend we finally got a chance to try out the production version of the ECU. It just so happened that the car that was volunteered was a beautiful, almost bone stock 91 convertible. The car had only an RB header and was still breathing through the stock main cat. On the dyno the car just did not want to pull over 6000 rpm with the stock ECU. Power peaked at 122.8 whp @ 5750. With the mod ECU we were able to lean it out, make around 13 more peak hp, and broaden the power band by about 1000 rpm! Good gains. I'll admit not completely relavent to an ITS car but we were only trying to prove that we did indeed have control of fuel and ignition. I'm also posting the a/f logs from this session. The first log represents the stock ECU. The second what were achieved with the mod ECU. These are relavent to an ITS car. Again, stock timing was used.

Stock ECU Dyno
http://www.ludwigmotorsports.com/rx7...stock_dyno.jpg

Mod ECU Dyno
http://www.ludwigmotorsports.com/rx7...u/mod_dyno.jpg

Stock ECU v. Mod ECU
http://www.ludwigmotorsports.com/rx7.../stock_net.jpg

Stock ECU A/F Log
http://www.ludwigmotorsports.com/rx7..._stock_log.jpg

Mod ECU A/F Log
http://www.ludwigmotorsports.com/rx7..._mod_log_2.jpg

Quote:

I'll pre-order for an S4 ECU at that price.
[/b]

We already have the street version of the S4 ECU. My guy that's building the boards says he can do the ITS internal connector but I want to make sure all the other ITS specific goodies from the S5 ECU make it into the S4 unit. Drop me an email if you haven't already and I'll keep you updated.

[email protected]