Printable View
Am in the midst of purchasing a header for an IT spec '89 CRX Si. Stories are conflicting concerning whether or not the D series motors will benefit from a 4-1 like the B series ? Is the top end gain on the 4-1 worth the relative loss in midrange compared with a 4-2-1 setup? http://Forums.ImprovedTouring.com/it/confused.gif Preference on brand ? Had planned on running a 2.5" pipe from the header back.
Thank you,
Robert J.
[This message has been edited by Mr. Noodles (edited January 17, 2004).]
We are using a DC Sports 4-2-1 header and a high flow CAT. This is followed by a long resonator and turn down. The tubing is 2.5" from the collector back. So far I have not noticed any real difference in performance from 3500-7000.
The components behind the collector are there because the car remains street legal.
What is also important is that one must Dyno the car to determine what is happening. DC products have been tested a number of times.
------------------
Grandpa's toys-modded suspensions and a few other tweaks
'89 CRX Si-SCCA ITA #99
'99 Prelude=a sweet song
'03 Dodge Dakota Club Cab V8-Patriot Blue gonna tow
high flow cat?
As in convertor-required for street cars. We have not yet yanked all the pollution stuff off. That is why it is there. It is also a benefit as it acts as a sort of resonator too.
------------------
Grandpa's toys-modded suspensions and a few other tweaks
'89 CRX Si-SCCA ITA #99
'99 Prelude=a sweet song
'03 Dodge Dakota Club Cab V8-Patriot Blue gonna tow
When you say you have not noticed any real difference, are you comparing the current setup to the oe configuration? I have heard that the oe setup works [ outside of the restrictive cat ] well for an IT spec head. I have no experience with the D16 and appreciate any feedback. http://Forums.ImprovedTouring.com/it/smile.gifQuote:
Originally posted by jc836:
We are using a DC Sports 4-2-1 header and a high flow CAT. This is followed by a long resonator and turn down. The tubing is 2.5" from the collector back. So far I have not noticed any real difference in performance from 3500-7000.
Thank you,
Robert J.
I cannot say for sure since we ran the car with the full stock exhaust initially. The engine does rev a bit more freely, in my opinion, with the DC and setup we now have. Again I have no dyno data and have not run the engine without a CAT. Sorry if this a bit vague-there are others here with far more serious setups that can answer too.
------------------
Grandpa's toys-modded suspensions and a few other tweaks
'89 CRX Si-SCCA ITA #99
'99 Prelude=a sweet song
'03 Dodge Dakota Club Cab V8-Patriot Blue gonna tow
i posted a response to someones post titled "need more top end" or something like that. I included a link to some dyno charts of before and after. the guy used a Bisimoto header on an utterly stock D-series 1.6 motor. these gains were throughout the RPM band and especially in the ranges you would be running. the engine used had many many miles on it and slightly enlarged exhaust ports already. its a stepped tube design using pressure waves and all that for scavenging....etc....despite the price, people swear by them! plus a really cool bundle of snakes is hard to beat. its a 4-1 with the curves and shapes made by science not just equal length alone.
ah, here it is. a message board post about the header and the experiences the lucky owner had with it.
http://pub161.ezboard.com/fbseriesalternat...picID=283.topic
the guys website. he is working now on a design that acts like a 2-stroke pipe for a 4 stroke car. using all kinds of black-magic. he is extremely well respected in the field.
www.bisimoto.com
[This message has been edited by airpiraterob (edited January 19, 2004).]
[This message has been edited by airpiraterob (edited January 19, 2004).]
Thanks for the update on the Bisimoto header. I've seen one similar, by AR-N. Both of these models use equal length serpentine headers that look like something off a F1 car. Cost is usually 2-3x the going rate for conventional 4-1's and I'm curious as to their impact versus conventional. I'd pay the price if I could find some dyno comparisons.
I'll let you know what I decide. Thanks again for the feedback.
Robert J.
I had 4-1's, I liked the way they felt more "online" than the 4-2-1's i replaced . The power band area to me felt better with 4-1 Mugens!
I have been doing a similar search for the B-series engine. What gives the most horsepower? What I've found is pretty similar to what you guys have talked about: Bisimoto, AN-R, HyTech, or SMSP. Only problem is they're sooooo expensive - best in the biz though. They're customers swear by them.
Bisimoto B-Series header:
http://www.automotivetech.org/photop...5bisibnew1.jpg
Bisimoto D-Series header:
http://www.exospeed.com/pictures/bisiheaderfront.jpg
Bisimoto D-Series Header Dyno Plot:
http://www.exospeed.com/pictures/bisiheaderdyno2.jpg
AN-R Standard B-Series Header:
http://www.an-r.com/images/stand2.JPG
AN-R Compact Version B-Series:
http://www.an-r.com/images/DSC03860.JPG
AN-R D-Series Header:
http://www.an-r.com/images/dheader.jpg
AN-R merge collector (badass):
http://www.burnsstainless.com/MergeC...utaway_big.gif
AN-R H-series dyno plot (all I can find, sorry):
http://www.an-r.com/Hdyno.jpg
[This message has been edited by R2 Racing (edited January 23, 2004).]
[This message has been edited by R2 Racing (edited January 23, 2004).]
We've used the 4-2-1 DC header before - it's a good header. Three years ago we tried a 4-1 header done by Walt Puckett at Delta Group Motorsports. We've ran it on the dyno and have been running this unit on the track since then on two different ITA CRXs. I highly recommend it. Quite a few other Honda IT racers use this header. It is great for top end (especially after 6K) and that's exactly what is needed to make the d16 fast on long straights. Get this header from www.opmautosports.com or from Walt Puckett at (704) 434-8046. Good luck.
------------------
Alex
#2 ita
Hracer....
What sort of results did the Pucket header give over the DC sports 4-2-1?
I have a DC sports header, I cut off the smallish outlet at the collector and welded on a 2-1/4" stainless tube, a braided flexjoint, and stainless 2-1/4" tube to a supertrapp at the back.
I'd be REALLY interested in real numbers comparing these two headers.
Thanks!!
Jon,
Different engines and exhaust systems have an effect on the outcome, but generally we see a 2-3 hp gain over the DC. The biggest difference we see is the engine continues to make power at higher rpm.
Walt
I think I just shorted out my keyboard, drooling over all those pipes!!!!!!
-T
So, 2-3hp peak... assuming about 6k rpm.
What sort of gains, then, at 6500? 7000?
7500? http://Forums.ImprovedTouring.com/it/smile.gif
Thanks,
Jon
PS - Since you've no doubt played with this, what would the "ultimate" exhaust for the D16A6 motor be?
If you want to keep at a secret, you can email me at [email protected] http://Forums.ImprovedTouring.com/it/smile.gif
Horsepower this horsepower that--dyno this dyno that--The real skinny is the DC SPort 4-2-1 is an overall good header,better suited for a short twisty track,OPM's 4-1 or a simular header is about 2-3 car length's faster on the medium to long tracks.You really will not notice any difference until you get on the straight's.One thing to consider is that if you like to leave the cement alot--the 4-1 does' not fit under the car as well.The 4-2-1 fits much tighter to the oil pan with a little more ground clearance.
AND---you have to do a few more things to the car to gain any of the power from that header($450)--about $300 for the DC Sport) which is a upgraded ECU,new final drive,etc.
The only way to keep up with the fast Honda's is do everything to the car that you can and drive that MoFo like you "stolt it".
D.V.
former CRX'er--currant SM driver
I can't find an address or web site for Bisimoto headers.Can anyone help. Thanks!
Quote:
Originally posted by ErnieJ:
I can't find an address or web site for Bisimoto headers.Can anyone help. Thanks!
www.exospeed.com & click on the Bisimoto Header section (top right)
R2Quote:
Thanks for the help finding Bisimoto.
2-1/2" is too big for an ITA D16A6 engine. A 4-1 can be built to gain torque in the mid range while also picking up horsepower int he upper range.