View Full Version : quicker removal of 1st gen front rotors
John MacKechnie
02-10-2004, 10:27 PM
Does anyone have a trick for speeding up the job of removing the front brake rotors on a 1st. Gen RX-7. I have ground down a 14 mm wrench to fit better behind the bracket that holds the caliper, but it is still a pain to get at it. Any ideas would be greatfully appreciated.
John MacKechnie
83rx701
02-11-2004, 12:00 AM
I found that if I pulled down on the top of the bracket after I took the top bolt out and move the bracket up and down it loosen the lower bolt so I could get an open end wernch in to remove it. I had to use some persuasion to get the bracket to move but once it did I had no problem getting the bolt out.
Lou I
NER ITA #79 RX7
RX767
02-11-2004, 10:52 AM
John,
That bolt is a PITA. I use a 14mm long box wrench and I wedge a square shafted Craftsman screwdriver behind it to hold it on. I am able to get the box wrench on far enough on that I can break it loose, and I then use the open end to spin it off.
Bill Emery
Glen Region
ITA#23
Festus E. Simkins
02-11-2004, 12:15 PM
When I put my brake ducts on I ground down the edge of the caliper mounting bracket so a box wrench would fit the bolt head. Only had to do this on the top bolt. I took off very little material on the bracket. It seems to work pretty good. I can change a rotor in about 15-20 minutes if everything else goes well.
Drive well.
ddewhurst
02-11-2004, 02:52 PM
Ditto to to the method used by Bill. Works great.
Have Fun http://Forums.ImprovedTouring.com/it/wink.gif
David
Scott Nutter
02-11-2004, 07:37 PM
I remove the rear bolt from the bottom of the strut, loosen the front one, and wa-la rotate the assembly and use a socket on that nasty little bolt.
I too can change the rotor in ~15 minutes, although the first time on an aquired Rx7, often takes longer http://Forums.ImprovedTouring.com/it/smile.gif
Marcus Miller
02-12-2004, 01:10 AM
Originally posted by Scott Nutter:
I remove the rear bolt from the bottom of the strut, loosen the front one, and wa-la rotate the assembly and use a socket on that nasty little bolt.
I too can change the rotor in ~15 minutes, although the first time on an aquired Rx7, often takes longer http://Forums.ImprovedTouring.com/it/smile.gif
I use an identical procedure; the last one took ~20 minutes including installing a new inner bearing. . . .
Marcus
Go to Sears and buy a combination 12/14 mm OFFSET box end wrench. It has a 12mm 12 point box end on one side, a 14mm 12 point box end on the other. Each box end is offset ~1/2 inch from the handle. It fits right into the caliper bracket and gives your knuckles extra clearance. Also handy for those pesky drive shaft bolts!
Tak
#29 ITA SFR SCCA
buy the turn in spacers from G-Force and the problem is gone.
Speed Raycer
02-19-2004, 05:12 PM
Originally posted by 7'sRracing:
buy the turn in spacers from G-Force and the problem is gone.
Ding! (Lightbulb just turned on upstairs) That's why the calipers came off so quickly on my new RX! As I was removing them I was thinking "hmmmm, this is going awfully quick."
In my defence, the spacers were already installed when I bought the car.
------------------
Scott
It's not what you build...
it's how you build it
http://www.angelfire.com/mo3/rudder_racing/images/RX7_Pictures/SRsRX/sig58.jpg (http://www.izzyscustomcages.com) http://www.angelfire.com/mo3/rudder_racing/images/IzzysImgs/IzzysLogoDSsmall.jpg (http://www/izzyscustomcages.com)
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.