RX7 guys help with dash / cage ??????

[ROBTRLRDR]

hi guys
i was wanting to know how you cut or modified your dash / console for the cage and the cross member. the tube that would pass through the console area.
i tried to cut as little as possible at the sides of the dash. but the center console is so brittle it just cracks when i move it a bit.
88 na , post some pics if you have them.
thanks
robert

[Chris Wire]

Sorry Robert, but my cage goes through my dash. Although the pics on page 2 of my web page, http://home.mindspring.com/~twire , don't show the dash installed, I have since fit the dash and I only cut it in 3 places. The two front down tubes and the end of the dash where the X bar goes.

------------------
Chris Wire
Team Wire Racing
ITS Mazda RX7 #35
[email protected]

[ddewhurst]

Robert, I race a Spec-7 there for I can not do the dash cross tube. On this site if you were to click on Tech Center & then click on Tech Photos you will find a bunch of photos of a CRX complete roll cage/dash bar. The dash will show a horizontal tube with one diagonal from near the center going to each side tube. Upon doing something for the first time it will take considerable thinking/planning & trial.

------------------
Have Fun ;)
David Dewhurst
CenDiv Milwaukee Region
Spec-7 #14

[balz]

Robert,

Check out the various directories on my site...you'll see a lot of the work we did.

www.balz.myip.org/Racing (http://www.balz.myip.org/Racing) Stuff

Best regards,



------------------
Balz
#67 IT-7
www.balz.myip.org
"I live my life one Apex (seal) at a time"

[ddewhurst]

Frank, when I click on your address I get a ERROR 404. No site......... http://Forums.ImprovedTouring.com/it/frown.gif

[ROBTRLRDR]

THANKS GUYS
the only way i could to the balz site was to copy and paste the address and delete the "/racing". then the site loaded ok.
thanks
robert

[Speed Raycer]

It's a 1st gen, but there are a few pics on our website of our cage. Click the pic below then look for the RX7 link on the sidebar.

------------------
Scott
It's not what you build...
it's how you build it
http://home.swbell.net/srhea66/AllThreeProjectsRealSmall.jpg (http://www.angelfire.com/mo2/radrodder)
http://home.swbell.net/srhea66/PFMSigPic.jpg (http://www.pfmracing.com) http://home.swbell.net/srhea66/replica2small.jpg
E-mail me for deals on
Lightweight Replica Blocks!

[ROBTRLRDR]

thanks guys.
robert

[balz]

sorry guys....

Physically type in the URL and it will work.

The address to my site is www.balz.myip.org (http://www.balz.myip.org)

I have a directory listing with a TON of pics laying below it (Racing Stuff).

The actual link is... http://www.balz.myip.org/racing%20stuff/

%20 = a "space" in html code. Most browsers will add this for you...sorry!

Frank



------------------
Balz
#67 IT-7
www.balz.myip.org
"I live my life one Apex (seal) at a time"

[balz]

sorry guys....

Physically type in the URL and it will work.

The address to my site is www.balz.myip.org (http://www.balz.myip.org)

I have a directory listing with a TON of pics laying below it (Racing Stuff).

The actual link is... http://www.balz.myip.org/racing%20stuff/

%20 = a "space" in html code. Most browsers will add this for you...sorry!

Frank



------------------
Balz
#67 IT-7
www.balz.myip.org
"I live my life one Apex (seal) at a time"